The generic-rk3568 does not reset the gmac phy, causing the kernel to
fail to initialize gmac during cold boot with the error message
"mdio_bus stmmac-1: MDIO device at address 1 is missing."
Adding a dedicated uboot for EasePi R1 to resolve this issue.
The EasePi R1's DTS hasn't been merged into the Linux release yet,
so it cannot be submitted to the upstream u-boot.
Fixes: ef093299db ("uboot-rockchip: add support for LinkEase EasePi R1")
Signed-off-by: Liangbin Lian <jjm2473@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20772
(cherry picked from commit 5dff7b45d3)
With changes:
1. Reorder patch file names (`105-*` to `106-*`).
2. configs/easepi-r1-rk3568_defconfig needs CONFIG_SPL_PAD_TO on u-boot 2024.10.
Signed-off-by: Liangbin Lian <jjm2473@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20744
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for esmt F50L1G41LC flash chip. It is used in some recent
Cudy devices.
(cherry picked from commit c84025dea2)
Link: https://github.com/openwrt/openwrt/pull/20963
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This board is also as known as E-Life ETR631-T/ETR635-U.
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB DDR3
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain telnet access:
1. Login into web interface, and download the configuration.
2. Uncompress the configuration:
* Enter fakeroot if you are not login as root.
tar -zxf <filename>.tar.gz
3. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
4. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; telnetd; ) &
5. Repack the configuration:
tar -zcf backup.tar.gz etc/
6. Upload new configuration via web interface, now you can connect to
KOMI A31 via telnet.
Flash instructions:
1. Connect to KOMI A31, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-konka_komi-a31-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-konka_komi-a31-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20357
(cherry picked from commit 8a7de107d8)
[rebase uboot patches upon 24.10 branch]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20595
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for the Lunzn FastRhino R66S board.
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/19990
(cherry picked from commit 678536740e)
[rebase patches upon 24.10 branch]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20618
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently, building at91 subtargets via image builder will fail as the
required built at91bootstrap is not present in the image builder at all
since its presumed to be in the binary directory which obviously does not
exist yet.
So, lets install the at91bootstrap binary into image staging directory and
use that instead
Link: https://github.com/openwrt/openwrt/pull/18414
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit a947be41b7)
Currently, building at91 subtargets via image builder will fail as the
required built u-boot is not present in the image builder at all since its
presumed to be in the binary directory which obviously does not exist yet.
So, lets install the u-boot binary into image staging directory and use
that instead.
Link: https://github.com/openwrt/openwrt/pull/18414
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 4724331d70)
Currently, tfa-layerscape packages are being included in the individual
profile DEVICE_PACKAGES but using the feature that allows skipping their
inclusion in the end image package list if prefixed with a tilde(~) which
was added in:
377b66990b ("build: introduce support to declare skip package")
But it not added to Image Builder so currently trying to build layerscape
device images in Image Builder will fail with:
ERROR: '~trusted-firmware-a-ls1012a-frdm' is not a valid world dependency, format is name(@tag)([<>~=]version)
So, instead of having to rely on support for skipping package installation
and declaring the individual TFA packages in DEVICE_PACKAGES we can just
do what other targets do and set BUILD_DEVICES so that TFA packages are
automatically set.
Fixes: #18412
Link: https://github.com/openwrt/openwrt/pull/18462
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 03ab770da5)
This is a smart door lock device equipped with OpenWrt 14.07 OEM
modified version Qdwrt
The OEM has closed down, This commit is intended to maximize the
remaining value of these devices. It can flash OpenWrt to become
an AP
Specification:
- SoC: MediaTek MT7628NN
- Flash: 8 MB
- RAM: 64 MB
- Power: DC 5V - 25V
- Ethernet: 1 x RJ45 (10/100 Mbps)
- Wireless radio: 802.11n 2.4g-only
- On-Board LED:
Status 1: GPIO/43 active-low
Status 2: GPIO/44 active-low
Power: AlwaysOn
- Button:
WPS / RESET: GPIO/14 active-low
- Bluetooth: CC2541 via UART1 (ttyS1) and GPIO/26-29
- RFID: MF RC522 on I2C@28
- RTC: DS1339 on I2C@68
- Shell (via CON1 cable)
- LED (Swipe card area):
- Green GPIO/3 active-high
- Red GPIO/11 active-high
- Matrix keypad: (active-low)
GPIO/20 GPIO/21 GPIO/19 (Rows)
GPIO/24 1 2 3
GPIO/25 4 5 6
GPIO/22 7 8 9
GPIO/23 BACK 0 ENTER
(Cols)
- UART: 1 x UART on PCB - 57600 8N1
- GPIO Relay: GPIO/42 active-high
- GPIO Buzzer: GPIO/15 active-high
Warning:
The original firmware does not use the device tree.
This device tree is written based on the content of /sys/devices/platform
and has been tested
Note:
- On the device, matrix keypad rows actually are columns, and the columns actually are rows
- The key code of the CLEAR key of the matrix keypad is BACK in the original firmware.
Issue:
- No drivers in mainline kernel for RFID and Bluetooth.
Flash Instruction:
Using SSH/Telnet:
1. Connect the board to the computer via RJ45 Ethernet
2. Login 10.10.10.1 with root password "szqdingnet123" (SSH Port 22, Telnet Port 9900)
3. Download openwrt firmware on the computer.
4. Setup a http server on computer. And use wget download openwrt firmware from computer
5. Use command "mtd -r write openwrt-ramips-mt76x8-qding_qc202-squashfs-sysupgrade.bin firmware"
to flash
Using U-Boot WebUI:
1. Configure PC with a static IP address 10.10.10.2/24.
2. Open http://10.10.10.1
3. Use "mkqdimg -B qc202 -f openwrt-ramips-mt76x8-qding_qc202-squashfs-sysupgrade.bin" to
make image.
4. Upload factory.bin via U-Boot WebUI.
Original Firmware Dump / More details:
https://blog.gov.cooking/archives/research-qianding-smart-locker-and-flash.html
Original U-Boot firmware image tools:
https://gitlab.com/CoiaPrant/mkqdimg
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Tested-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17471
(cherry picked from commit b2f814fed4)
Link: https://github.com/openwrt/openwrt/pull/20159
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Radxa ROCK 4SE[1] is a single board computer using the Rockchip
RK3399-T.
Hardware
--------
- Dual-core Cortex-A72 and quad-core Cortex-A53 CPU
- Mali-T860MP4 GPU
- LPDDR4 4GB RAM
- M.2 M Key slot (PCIe 2.1 x4)
- eMMC connector
- microSD card slot
- Wi-Fi 5 (not supported)
- Gigabit Ethernet with PoE support (additional PoE HAT required)
- USB 3.0 Type-A OTG port
- USB 3.0 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- USB Type-C power port (5V only)
- 40 Pin GPIO header
[1] https://radxa.com/products/rock4/4se
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to the micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/17554
(cherry picked from commit 6690f551c8)
Link: https://github.com/openwrt/openwrt/pull/19940
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Radxa ROCK 4C+[1] is a single board computer with dual HDMI using
the Rockchip RK3399-T.
Hardware
--------
- Dual-core Cortex-A72 and quad-core Cortex-A53 CPU
- Mali-T860MP4 GPU
- LPDDR4 4GB RAM
- eMMC connector
- microSD card slot
- Wi-Fi 5 (not supported)
- Gigabit Ethernet with PoE support (additional PoE HAT required)
- USB 3.0 Type-A OTG port
- USB 3.0 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- USB Type-C power port (5V only)
- 40 Pin GPIO header
[1] https://radxa.com/products/rock4/4cp
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to the micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/17554
(cherry picked from commit 18925614c0)
Link: https://github.com/openwrt/openwrt/pull/19940
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add uboot-envtools support for Gateworks venice boards based on i.MX8M
SoC's (imx_cortexa53) which boot from and store their U-Boot env on
eMMC boot0 hardware partition.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/19347
(cherry picked from commit 29f7c0ef97)
Link: https://github.com/openwrt/openwrt/pull/19437
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This allows us to use the full size of nand, which increases ubi size
from 64M to 122.25M.
If you are at factory firmware, please refer commit 63b8d98dd0 ("mediatek: add support for Cudy TR3000 v1")
to boot into OpenWrt initramfs (stock layout).
Flash instructions:
1. Login into the device and backup everything, especially 'Factory' part.
1. Unlock mtd partitions:
opkg update && opkg install kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
3. Write new BL2 and FIP
mtd write openwrt-mediatek-filogic-cudy_tr3000-v1-ubootmod-preloader.bin BL2
mtd write openwrt-mediatek-filogic-cudy_tr3000-v1-ubootmod-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Tested-by: Yangyu Chen <cyy@cyyself.name>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 6f8c58bfd8)
[sync uboot defconfigs with 24.10 branch, change apk to opkg]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/18945
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* commit '5ff7149a08df0a5f408ceb48c1b0ca2a40b49b3e': (142 commits)
OpenWrt v24.10.2: revert to branch defaults
OpenWrt v24.10.2: adjust config defaults
ramips: mt7621: include uboot-envtools in some missed devices
ipq806x: fix Extreme Networks AP3935 LAN/WAN ports
ipq806x: fix Extreme Networks AP3935 LAN LED order
kernel: Fix IPv6 UDP fragmentation regression
wifi-scripts: add missing mesh_nolearn
hostapd: fix generating own neighbor report for dynamically added/changed interfaces
hostapd: fix dealing with mac address changes for the primary BSS
perf: disable slang support
mediatek: filogic: add support for Cudy WR3000E v1
mediatek: Create common DTSI for WR3000H and WR3000S
mediatek: filogic: fix 2.5G phy compatible for WR3000H
mediatek: filogic: Cudy WR3000H: Fix SUPPORTED_DEVICES
mediatek: filogic: Add support for cudy wr3000h
tools/expat: bump to 2.7.1 to fix several CVEs
tools/patch: bump version to v2.8
strace: Update to version 6.12
arm-trusted-firmware-stm32: bump to v2.10.17
include/trusted-firmware-a.mk: support LTS releases
...
Signed-off-by: Liangbin Lian <jjm2473@gmail.com>
# Conflicts:
# package/kernel/r8101/Makefile
# package/kernel/r8125/Makefile
# package/kernel/r8126/Makefile
# package/kernel/r8127/Makefile
# package/kernel/r8168/Makefile
The Xiaomi MiWiFi 3A wireless router has a similar system architecture as the Xiaomi Mi 4A router, which is already officially supported by OpenWrt.
Product website: https://www.mi.com/miwifi3a
Device specification
--------------------
SoC: MT7628AN MIPS_24KEc @ 580 MHz 2.4G-bgn 2x2
WiFi: MT7612EN 5G-an, ac 80 MHz 2T2R
Flash: 16 MB
DRAM: 64 MB
Switch: MT7628AN (integrated in SoC)
Ethernet: 1 x 10 /100 Mbps
USB: None
Antennas: 2 x 2,4 GHz and 2 x 5 GHz (all are external and non-detachable)
LEDs: blue/red/amber
Buttons: Reset
Serial: 115200,8n1
MAC addresses as verified by OEM firmware:
------------------------------------------
use address source
LAN *:DD factory 0x28
WAN *:DD factory 0x28
2g *:DE factory 0x4
5g *:DF factory 0x8004
OEM firmware uses VLAN's to create the network interface for WAN and LAN.
Bootloader info:
----------------
The stock bootloader uses a "Dual ROM Partition System".
OS1 is a deep copy of OS2.
The bootloader starts OS2 by default.
To force start OS1 it is needed to set "flag_try_sys2_failed=1".
How to install:
---------------
1- Use OpenWRTInvasion to gain Telnet, SSH and FTP access: https://github.com/acecilia/OpenWRTInvasion
[IP: 192.168.31.1 | Username: root | Password: root | FTP-Port: 21]
2- Connect to router using telnet or ssh.
3- Backup all partitions. Use command "dd if=/dev/mtd0 of=/tmp/mtd0". Copy /tmp/mtd0 to computer using ftp.
4- Copy openwrt-ramips-mt76x8-xiaomi_miwifi-3a-squashfs-sysupgrade.bin to /tmp in router using ftp.
5- Enable UART access and change start image to OS1.
nvram set uart_en=1
nvram set flag_last_success=1
nvram set boot_wait=on
nvram set flag_try_sys2_failed=1
nvram commit
6- Erase OS1 & OS2 and install OpenWrt
mtd erase OS1
mtd erase OS2
mtd -r write /tmp/openwrt-ramips-mt76x8-xiaomi_miwifi-3a-squashfs-sysupgrade.bin OS1
Credits:
--------
This PR is based on the work of Zehao Zhang (Github: @ZZH-Finalize) that he had published in the PR: #15698
Signed-off-by: Olgun Demir <olgun.demir@mail.com.tr>
Link: https://github.com/openwrt/openwrt/pull/18427
(cherry picked from commit c3b8108a2b)
Link: https://github.com/openwrt/openwrt/pull/18550
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for Mercusys MR80X(EU) v3 router.
Device specification:
- SoC: Mediatek MT7981b, Cortex-A53, 64-bit
- RAM: 512MB
- Flash: SPI NAND GigaDevice GD5F1GQ5UEYIGY (128 MB)
- Ethernet: 4x 100/1000 Mbps LAN1,LAN2,LAN3 & WAN
- Wireless: 2.4GHz (802.11 b/g/n/ax)
- Wireless: 5GHz (802.11 a/n/ac/ax)
- LEDs: 1 orange and 1 green status LEDs, 4 green gpio-controlled LEDs
on ethernet ports
- Buttons: 1 (Reset)
- Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI
slots contain "seconduboot" (also U-Boot 2022.01-rc4)
Installation (UART):
- Place OpenWrt initramfs-kernel image on tftp server with IP 192.168.1.2
- Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'.
- Set the uboot environment for startup.
setenv tp_boot_idx 0; setenv bootcmd bootm 0x46000000; saveenv
If the bootarg is set to boot from ubi1, also change it to ubi0.
- Load and run OpenWrt initramfs image.
setenv serverip 192.168.1.2; setenv ipaddr 192.168.1.1; tftpboot initramfs-kernel.bin; bootm
- Login as root via SSH (IP 192.168.1.1, port 22)
- Upload OpenWrt sysupgrade.bin image to the /tmp dir of the router
- Run sysupgrade:
sysupgrade -n /tmp/sysupgrade.bin
Recovery:
- Press Reset button and power on the router.
- Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware.
Stock layout:
0x000000000000-0x000000200000 : "boot"
0x000000200000-0x000000300000 : "u-boot-env"
0x000000300000-0x000003500000 : "ubi0"
0x000003500000-0x000006700000 : "ubi1"
0x000006700000-0x000006f00000 : "userconfig"
0x000006f00000-0x000007300000 : "tp_data"
ubi0/ubi1 format:
U-Boot at boot checks that all volumes are in place:
+-------------------------------+
| Volume Name: uboot Vol ID: 0|
| Volume Name: kernel Vol ID: 1|
| Volume Name: rootfs Vol ID: 2|
+-------------------------------+
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| label | 94:0C:xx:xx:xx:12 | label |
| WAN | 94:0C:xx:xx:xx:13 | label+1 |
| LAN | 94:0C:xx:xx:xx:12 | label |
| WLAN 2g | 94:0C:xx:xx:xx:11 | label-1 |
| WLAN 5g | 94:0C:xx:xx:xx:10 | label-2 |
+---------+-------------------+-----------+
label MAC address was found in UBI partition "tp_data", file
"default-mac".
Signed-off-by: Schneider Azima <Schneider-Azima12@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/18181
(cherry picked from commit 7921e48d43)
Signed-off-by: Schneider Azima <Schneider-Azima12@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/18522
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
**Huasifei WH3000 eMMC / Fudy MT3000**
Portable Wi-Fi 6 travel router based on MediaTek MT7981A SoC.
MT7981B+MT7976CN+RTL8221B Dual Core 1.3GHZ
**Specifications**
SoC: Filogic 820 MT7981A (1.3GHz)
RAM: DDR4 1GB
Flash: eMMC 8GB
WiFi: 2.4GHz and 5GHz with 3 antennas
Ethernet:
1x WAN (10/100/1000M)
1x LAN (10/100/1000/2500M)
USB: 1x USB 3.0 port
Two buttons: power/reset and mode (BTN_0)
LEDS: blue, red, blue+red=pink
UART: 3.3V, TX, RX, GND / 115200 8N1
**Installation via U-Boot rescue**
1. Set static IP 192.168.1.2 on your computer and default route as 192.168.1.1
2. Connect to the WAN port and hold the reset button while booting the device.
3. Wait for the LED to blink 5 times, and release the reset button.
4. Open U-boot web page on your browser at http://192.168.1.1
5. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
6. Wait for the router to flash the new firmware.
7. Wait for the router to reboot itself.
**Installation via sysupgrade**
Just flash sysupgrade file via [LuCI upgrade page](http://192.168.1.1/cgi-bin/luci/admin/system/flash) without saving the settings.
**Installation via SSH**
Upload the file to the router `/tmp` directory, `ssh root@192.168.1.1` and issue a command:
```
sysupgrade -n /tmp/openwrt-mediatek-filogic-huasifei_wh3000-emmc-squashfs-sysupgrade.bin
```
**Factory MAC**
You can find your Factory MAC which is mentioned on the box at `/dev/mmcblck0p2` partition `factory` starting from `0x4`
```
dd if=/dev/mmcblk0p2 bs=1 skip=4 count=6 | hexdump -C
```
**Enlarging a partition**
Though device has 8GB eMMC, it uses only 2GB `/dev/mmcblck0p6` as `rootfs` for `/rom` and `/overlay` leaving `/dev/mmcblck0p7` as empty unused space.
```
sgdisk -p /dev/mmcblk0
```
```
Disk /dev/mmcblk0: 15269888 sectors, 7.3 GiB
Sector size (logical/physical): 512/512 bytes
Disk identifier (GUID): 2BD17853-102B-4500-AA1A-8A21D4D7984D
Partition table holds up to 128 entries
Main partition table begins at sector 2 and ends at sector 33
First usable sector is 34, last usable sector is 14942174
Partitions will be aligned on 1024-sector boundaries
Total free space is 11197 sectors (5.5 MiB)
Number Start (sector) End (sector) Size Code Name
1 8192 9215 512.0 KiB 8300 u-boot-env
2 9216 13311 2.0 MiB 8300 factory
3 13312 21503 4.0 MiB 8300 fip
4 21504 29695 4.0 MiB 8300 config
5 29696 62463 16.0 MiB 8300 kernel
6 62464 4256767 2.0 GiB 8300 rootfs
7 4257792 14940159 5.1 GiB 8300
```
You can fix that by loading into `initramfs-kernel`, deleting empty `mmcblck0p7` partition and resizing `mmcblck0p6`
```
sysupgrade -F /tmp/openwrt-initramfs-kernel.bin
```
Install and run cfdisk
```
opkg update && opkg install cfdisk
cfdisk /dev/mmcblck0
```
- Select `mmcblck0p7` -> Delete
- Select `mmcblck0p6` -> Resize -> Write -> yes -> Quit
You will not see any difference in `cat /proc/partitions` after that but just flash a `sysupgrade` and you'll get the whole 7.3GB space for the `/overlay`.
Co-developed-by: hecatae <horus.ra@gmail.com>
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18220
(cherry picked from commit 99ea96c297)
Link: https://github.com/openwrt/openwrt/pull/18434
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This PR adds support for netis NX31 router.
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3 GHz
- RAM : 256 MiB DDR3
- Flash : SPI-NAND 128 MiB (ESMT)
- WLAN : MediaTek MT7976CN dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MIMO 2x2
- 5 GHz : a/n/ac/ax, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x3 (LAN, MediaTek MT7531AE)
10/100/1000 Mbps x1 (WAN, SoC internal phy)
- USB : No
- Buttons : Mesh, Reset
- LEDs : 1x Power (blue), unmanaged
1x Status (blue), gpio-controlled
1x WiFi 2.4 GHz (blue), gpio-controlled
1x WiFi 5 GHz (blue), gpio-controlled
3x LAN activity (blue), switch-controlled
1x WAN activity (blue), gpio-controlled
- Power : 12 VDC, 1 A
Installation
------------
1. Connect to the router using ssh (user: admin, pass: web interface
password)
2. Make mtd backup:
cat /dev/mtd0 | gzip -1 -c > /tmp/mtd0_spi0.0.bin.gz
cat /dev/mtd1 | gzip -1 -c > /tmp/mtd1_BL2.bin.gz
cat /dev/mtd2 | gzip -1 -c > /tmp/mtd2_u-boot-env.bin.gz
cat /dev/mtd3 | gzip -1 -c > /tmp/mtd3_Factory.bin.gz
cat /dev/mtd4 | gzip -1 -c > /tmp/mtd4_FIP.bin.gz
cat /dev/mtd5 | gzip -1 -c > /tmp/mtd5_ubi.bin.gz
3. Download mtd backup from the /tmp dir of the router to your PC using
scp protocol
4. Upload OpenWrt 'bl31-uboot.fip', 'preloader.bin' images to the /tmp
dir of the router using scp protocol
5. Write FIP and BL2 (replace bootloader):
mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-bl31-uboot.fip FIP
mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-preloader.bin BL2
6. Place OpenWrt
'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
the tftp server (IP: 192.168.1.254)
7. Erase 'ubi' partition and reboot the router:
mtd erase ubi
reboot
8. U-Boot automatically boot OpenWrt recovery image from tftp server to
the RAM
9. Upload OpenWrt 'sysupgrade.itb' image to the /tmp dir of the router
(IP: 192.168.1.1) using scp protocol
10. Connect to the router using ssh and run:
sysupgrade -n openwrt-mediatek-filogic-netis_nx31-squashfs-sysupgrade.itb
Return to stock
---------------
1. Unpack stock BL2 and FIP partitions backup
2. Upload stock BL2 and FIP partitions backup to the /tmp dir of the
router using scp protocol
3. Connect to the router using ssh and run:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd unlock FIP
4. Restore backup:
mtd write /tmp/mtd4_FIP.bin FIP
mtd write /tmp/mtd1_BL2.bin BL2
5. Erase ubi and reboot:
mtd erase ubi
reboot
6. Power off the router
7. Press Reset button and power on the router. Release the button after
~10 sec
8. Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware
Recovery
--------
1. Place OpenWrt
'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
the tftp server (IP: 192.168.1.254)
2. Press “Reset” button and power on the router. After ~10 sec release
the button.
3. Use OpenWrt initramfs system for recovery
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| LAN | dc:xx:xx:d1:xx:18 | label |
| WAN | dc:xx:xx:d1:xx:1a | label+2 |
| WLAN 2g | de:xx:xx:11:xx:19 | |
| WLAN 5g | de:xx:xx:71:xx:19 | |
+---------+-------------------+-----------+
The LAN MAC was found in 'Factory', 0x1fef20
The WAN MAC was found in 'Factory', 0x1fef26
The WLAN 2g/5g MAC prototype was found in 'Factory', 0x4
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18324
(cherry picked from commit d8002cb627)
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18438
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
