Specification:
The device is similar to the M30 but has only one LAN port and no WAN port.
- MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
- 512MB RAM
- 128MB NAND flash with two UBI partitions with identical size
- 1 multi color LED (red, green, blue, white) connected via GCA230718
- 2 buttons (WPS, reset, LED)
- 1 1Gbit LAN port
Disassembly:
- There are two screws at the power connector which must be removed. Afterwards the top case can be removed (it is clipped on, so some tools are required).
Serial Interface:
- The serial interface can be connected to the 4 pin holes on the board. Do NOT connect VCC.
- The pins are labelled on the PCB (RX, TX, GND)
- Settings: 115200, 8N1
MAC addresses:
- LAN MAC is stored in partition "Odm" at offset 0x8f
- WLAN MAC (2.4 GHz and 5GHz) is LAN MAC + 1
Reverting back to OEM firmware:
- There is currently no easy way to revert back to the OEM image
- The methods from M30 and M60 doesn't seem to work anymore
- If you plan to revert back to OEM firmware later, do the following steps before flashing OpenWrt:
- Boot from initramfs as described in "Flashing via U-Boot" but don't flash anything
- Instead, make a backup of UBI and UBI1 partition
- The created dumps must be written to the initial partitions to revert back to OEM
Flashing via Recovery Web Interface:
- Set your IP address to 192.168.200.10, subnetmask 255.255.255.0
- Press the reset button while powering on the device
- Keep the reset button pressed until the LED blinks red
- Open a Chromium based and goto http://192.168.200.50/ (recovery web interface)
- Download openwrt-mediatek-filogic-dlink_aquila-pro-ai-e30-a1-squashfs-recovery.bin
- Note: The recovery web interface always reports successful flashing, even if it fails
- After flashing, the recovery web interface will try to forward the browser to 192.168.0.1 (can be ignored)
- If flashing was successful, OpenWrt is accessible via 192.168.1.1
- The recovery image boots an initramfs image, flash the sys upgrade image to get to „normal“ OpenWrt mode
Flashing via U-Boot:
- Open the case, connect to the UART console
- Set your IP address to 192.168.200.2, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides openwrt-mediatek-filogic-dlink_aquila-pro-ai-e30-a1-initramfs-kernel.bin
- Supply the board with 12V
- Select "7. Load image" in the U-Boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
- The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
- Perform a sysupgrade using openwrt-mediatek-filogic-dlink_aquila-pro-ai-e30-a1-squashfs-sysupgrade.bin
- Reboot the device. OpenWrt should start from flash now
Flashing via OEM web interface is not possible, as it will change the active partition and OpenWrt is only running on the first UBI partition.
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22776
(cherry picked from commit 145bc7e52f2086c10b1705b6e708a954088b7c53)
Link: https://github.com/openwrt/openwrt/pull/22958
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
c0d5d8f83f
