Newer Cudy WR3000H units have a Motorcomm YT8821 PHY instead of a
Realtek PHY on the WAN port. Before this commit, the Motorcomm PHY
could not be autodetected by the kernel -- the PHY would show up as
just a generic clause 45 PHY and the proper driver would not be loaded.
The cause of the detection failure likely was that the YT8821 PHY was
held in reset during PHY detection. To fix this, move the reset GPIO
definition to the MDIO bus level. This reset line is deasserted before
the autodetection process, see also [1]. With this change, both Realtek
and Motorcomm PHYs can be supported with a single device tree.
[1]: https://lore.kernel.org/all/20251119134750.394655-1-horatiu.vultur@microchip.com/
Signed-off-by: Jakub Vaněk <linuxtardis@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21399
(cherry picked from commit 02f0efd60b423b4ce9b996f7c986dd68965a50d4)
Signed-off-by: Jakub Vaněk <linuxtardis@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21531
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit bed6f08c36f85479448af23a0ce4ca00dd09fa8e)
Recent Cudy WR3000H v1 units have a Motorcomm YT8821 2.5G PHY for
the WAN interface instead of the RTL8221B PHY used in earlier units,
so add kmod-phy-motorcomm to be able to use it.
Signed-off-by: Andrew MacIntyre <andymac@pcug.org.au>
[linuxtardis@gmail.com: slightly reworded the commit description]
Signed-off-by: Jakub Vaněk <linuxtardis@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21399
(cherry picked from commit dbafbab8769b92c8466ea83400280b4f549ace71)
Signed-off-by: Jakub Vaněk <linuxtardis@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21531
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 09e56437e8be4e0d85ab5697ec7a12b463a05397)
Include XHCI USB drivers on the Cudy WR3000P v1 router, the drivers are
required to be able to use the USB port for USD devices.
Closes: https://github.com/openwrt/openwrt/issues/21231
Fixes: 04e9d154f209 ("mediatek: filogic: add support for Cudy WR3000P v1")
Signed-off-by: Dmitry Mostovoy <dmitry.mostovoy@ceifx.com>
Link: https://github.com/openwrt/openwrt/pull/21281
(cherry picked from commit 9da57e2f828bc4a589b9a94e4cdf1b6ccdeb110e)
Link: https://github.com/openwrt/openwrt/pull/21405
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 8843108ff0fffb2abdc87465c323c97c7821df05)
The gmac definition has an offset of 1 compared to the label MAC.
Fixes: a55ab9e134 ("mediatek: filogic: prevent faulty mac address assignment")
Signed-off-by: Maximilian Baumgartner <aufhaxer@googlemail.com>
Link: https://github.com/openwrt/openwrt/pull/21560
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 687a2535d55f84a0daa2038b7e8736313cb2804e)
(cherry picked from commit 82f4ee5656d0126de24cf1cc2197c4194a31d6e9)
The SUPPORTED_DEVICES sets for both Maxlinear (v1) and Airoha (v2)
devices were identical, so sysupgrade was unable to detect when an
incorrect image was being installed. This caused "soft bricking" of
devices when a v1 image was installed on a v2 device, and vice versa.
Fix this by making the supported_devices distinct for each device
version, by renaming the devices with a version-specific name.
This is reflected in the file name and the image metadata.
Fixes: https://github.com/openwrt/openwrt/issues/20566
Fixes: https://github.com/openwrt/asu/issues/1525
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20632
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b71f4665cda10c284c9460409ae30fb9b0beecf8)
(cherry picked from commit dcf11c832a95595e6b919b88d6cd649bd9343a1f)
backport upstream commit 095151b235 (mediatek: fix pwn fan settings for
sinovoip bpi-r3 (v3))
Popular cheap PWM fans for this machine, like the ones coming in
heatsink+fan combos will not work properly at the currently defined
medium speed. Trying different pwm setting using a command
echo $value > /sys/devices/platform/pwm-fan/hwmon/hwmon1/pwm1
I found:
pwm1 value fan rotation speed cpu temperature notes
-----------------------------------------------------------------
0 maximal 31.5 Celsius too noisy
40 optimal 35.2 Celsius no noise hearable
95 minimal
above 95 does not rotate 55.5 Celsius
-----------------------------------------------------------------
Current cooling levels are:
cooling-levels = <255 96 0>;
Thus only cpu-active-high and cpu-active-low modes are usable.
This patch fixes cpu-active-medium settings for bpi-r3 board.
This patch may not be enough. Users may wants to tweak their thermal_zone0
trip points, thus tuning fan rotation speed depending on cpu temperature.
That can be done on the base of the following example:
=== example =========
# cpu temperature below 25 Celsius degrees, no rotation
echo 25000 > /sys/class/thermal/thermal_zone0/trip_point_4_temp
# cpu temperature in [25..32] Celsius degrees, normal rotation speed
echo 32000 > /sys/class/thermal/thermal_zone0/trip_point_3_temp
# cpu temperature above 50 Celsius degrees, max rotation speed
echo 50000 > /sys/class/thermal/thermal_zone0/trip_point_2_temp
=====================
Changes v2:
* put patch to a proper directory
* updated patch description
* tested with latest openwrt based on linux-6.6
Changes v3:
* use upstream linux patch
* update patch description
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21252
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 2916275a3d6cdda8bbc9decb5fd4df5e89a425a1)
cudy ap3000-v1 did not work correctly in failsafe mode
because the address 192.168.1.1 was missing on the eth0 inteface.
it was reachable via it's IPv6 link-local address however.
this commit fixes the issue.
Fixes: https://github.com/openwrt/openwrt/issues/20750
Signed-off-by: Martin Nadvornik <martin.nadvornik@gmx.at>
Link: https://github.com/openwrt/openwrt/pull/21172
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit e5cd6461c905184db8f49692f931b20fec4b819e)
(cherry picked from commit 58a0211f8201ab622b7b11d31629d6d755bd6526)
The ports are physically labelled in reverse order on the device.
This patch aligns logical names with physical ones.
LED order on front of device is correct after this patch.
Fixes: 9d66b8b312fb6a4087244ee3ee10e1ba1623df81
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Link: https://github.com/openwrt/openwrt/pull/20528
(cherry picked from commit 887cab883bc4b3e104b70e74af775522d060e1d4)
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Link: https://github.com/openwrt/openwrt/pull/21173
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 7aa929881e444ebc0ec0ae6cf027144db26392d1)
Fix Totolink X6000R image failing to upgrade via sysupgrade due to an
incorrect upgrade case. The fallback upgrade path used the NAND upgrade
routine, which caused the "layout volume not found" error on NOR flash
devices. By adding a specific case for this board, sysupgrade now uses
`default_do_upgrade`, which is compatible with the NOR flash layout.
Fixes: 7cd10ad
Signed-off-by: Ayra Hikari <ayrahikari@linuxmail.org>
(cherry picked from commit 7cd10add2de3c8227cf7383c7ca5cf3b12eeb822)
Link: https://github.com/openwrt/openwrt/pull/20674
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 30b7a5f27aa34aa3392a5f6e1e54b02d30934cde)
Specification :
- SOC : Mediatek MT7981B (1.3GHz)
- RAM : 256MB
- Flash : 16MB SPI NOR
- Ports : 4 LAN (1G) & 1 WAN (1G)
- WIFI : MediaTek dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MIMO 2x2
- 5 GHz : a/n/ac/ax, MIMO 2x2
- Buttons : Reset & WPS/Mesh
- LEDS : WAN (Green), Status (Red & Blue)
- Power : 12V1A
Install via OEM web ui:
Upload the sysupgrade image to firmware upgrade page on OEM web ui
Install via recovery / revert to stock firmware:
1. Unplug from power
2. Download the Sysupgrade (for openwrt installation) or OEM Factory image (for revert to stock firmware)
3. Set your computer ethernet IP to 192.168.1.X, subnet 255.255.255.0 (X=your chosen ip number ranging from 2-254)
4. Press and hold reset button while turn on / plug power adapter to the router. Wait untill ALL LAN green LED turn on, then release the reset button.
5. Plug the LAN cable from your computer into LAN 1 port then open web browser, and type in the address column : 192.168.1.1
6. Upload the sysupgrade / oem factory image
7. Wait until the router finished flashing (the router will reboot)
8. Set ethernet ip to dhcp
9. Open 192.168.1.1 (for openwrt install) / 192.168.0.1 (for OEM firmware)
Signed-off-by: Ari Kurniawan <noobhek@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20035
(cherry picked from commit 7cd10add2de3c8227cf7383c7ca5cf3b12eeb822)
Signed-off-by: Ari Kurniawan <noobhek@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20674
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 8db7b6ff53042848cb9212069b3ebec33076c38a)
ASUS TUF-AX4200Q(TUF 小旋风Pro WiFi6 AX4200) is a home router that adds an additional 2.5G Ethernet port to ASUS TUF-AX4200.
Hardware
- - - - - - - -
- SOC : MediaTek MT7986
- RAM : 512MB DDR3
- FLASH : 256MB SPI-NAND (Winbond W25N02KV)
- WIFI : Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
- ETH : MediaTek MT7531 Switch
MaxLinear GPY211C 2.5 N-Base-T PHY (WAN)
MaxLinear GPY211C 2.5 N-Base-T PHY (LAN)
- UART : 3V3 115200 8N1 (Pinout silkscreened / Do not ocnnect VCC)
Installation
- - - - - - - -
Vendor-UI Method:
1. Download or make the OpenWrt initramfs.trx image
2. Connect the PC via LAN to one of the yellow router ports and wait until your PC to get a DHCP lease.
3. Browse to http://192.168.50.1/
4. If your router is brand new, finish the setup process and log into the Web-UI.
5. Navigate to Administration -> Firmware Upgrade and upload the downloaded OpenWrt image.
6. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using SCP and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
TFTP Method:
1. Download the OpenWrt initramfs image.
Copy the image to a TFTP server reachable at 192.168.1.70/24.
Rename the image to tufax4200q.bin.
2. Connect the PC with TFTP server to the TUF-AX4200Q.
Set a static ip on the ethernet interface of your PC.
(IP address: 192.168.1.70, subnet mask: 255.255.255.0)
Connect to the serial console,
interrupt the autoboot process by pressing '4' when prompted.
3. Download & Boot the OpenWrt initramfs image.
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 tufax4200q.bin
$ bootm 0x46000000
4. Wait for OpenWrt to boot.
Transfer the sysupgrade image to the device using SCP and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
(based on support for ASUS RT-AX52 by achterin and trx image generation by remittor)
Link: https://github.com/openwrt/openwrt/pull/20900
(cherry picked from commit e7086d7a2fc00410df079b4897a47a823a36068d)
Signed-off-by: Brian Lee <larte332@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21036
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 237b1c29e15206554c27049bbb109311311534a9)
According to the factory uboot and firmware[1], the ubi size is set
to 512 MiB (0x20000000) and it exceeds the size of the flash, after
that the uboot and kernel resizes it to 114.5 MiB (0x7280000) instead
of 114.125 MiB (0x7220000). The mismatch of the ubi size causes
kernel fails to read ubi volumes and throws panic.
Trim whitespaces while at it.
1. https://github.com/immortalwrt/immortalwrt/issues/2123#issuecomment-3523744128
Fixes: c908fc7d9591 ("mediatek: add support for Zbtlink ZBT-Z8102AX v2")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20769
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d2fa070f7014e8b1144a23e343b31390e7f565ff)
[rebased upon 24.10 branch]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/21085
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 9fa8e7e9a3a98282fac09880b014e980e476796d)
Product name: Wavlink WL-WN536AX6 Rev a "Mighty LX2"
Product link: https://www.wavlink.com/en_us/product/WL-WN536AX6.html
Specifications:
SOC: MT7986AV
RAM: 512MB DDR4
Flash: 128MB SPI NAND
Ports: 4 LAN (1G) & 1 WAN (2.5G)
WIFI: MT7976PN + MT7975N
LEDs: 8 (STATUS, WIFI, WAN, LAN1, LAN2, LAN3, LAN4, PWR)
USB: 1 (3.0)
MAC table, same as stock firmware:
LAN: 80:3F:5D:xx:xx:x1 partition "hw" at 0x44e (ASCII)
WAN: 80:3F:5D:xx:xx:x2 partition "hw" at 0x460 (ASCII)
2G: 80:3F:5D:xx:xx:x3
5G: 80:3F:5D:xx:xx:x4
* Installation with OEM WebUI:
Note: Make sure PC is connected on LAN1 port. The OEM firmware has an unknown root password and settings are kept after upgrading firmware. Therefore, a customized Openwrt firmware is needed to remove the root password on login, by adding `passwd -d root` to /etc/init.d/bootcount. The WebUI does a filename check so the customized firmware is named accordingly.
1. Download modified firmware file `WAVLINK_WN536AX6-A_M36AX6_V250320-WO-437baca-modified.bin` from https://github.com/ses1er/firmware-misc/tree/main/wavlink/wl-wn536ax6a
2. Log into WebUI on default IP: http://192.168.20.1
3. Browse to More (top menu) -> System -> Firmware Upgrade.
4. Under `Local Upgrade` section, check the device to be upgraded and upload downloaded modified firmware. Click `UPLOAD FILE`, then `APPLY`
5. Wait about 2 minutes (ignore progress bar), and browse to http://192.168.20.1. You should see LUCI login page. Username is root and no password.
6. Browse to `System -> Backup/Flash Firmware`, click on `Flash Image`, click `Browse` and locate `openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-squashfs-sysupgrade.bin` file.
7. Uncheck `Keep settings and retain the current configuration` and click `Continue`.
8. Router will now be set to IP 192.168.1.1 which is the Openwrt default.
* Installation with UART:
Note: Having UART connected while cold booting the device will result in a kernel panic when initializing wifi. I've found this workaround:
1. Power off the device and ensure UART is not connected to PC.
2. Power up the device, when lights come on, plug in UART.
3. Warm boots and soft restarts will not cause kernel panic for the duration of device being powered on. Repeat steps for subsequent cold boots.
1. Configure TFTP server with IP 192.168.1.66. Copy `openwrt-mediatek-filogic-wavlink_wl-wn536ax6a-initramfs.itb` to TFTP root.
2. Interrupt boot by pressing 0.
3. Run the following in Uboot console: `setenv serverip 192.168.1.66; setenv ipaddr 192.168.1.1; tftpboot 0x46000000 openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-initramfs.itb; bootm`
4. Transfer `openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-squashfs-sysupgrade.bin` to device:
(`scp -O openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/`)
5. Run the following on device: `sysupgrade -n /tmp/openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-squashfs-sysupgrade.bin`
Signed-off-by: Qing W. <ses1er@gmail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://github.com/openwrt/openwrt/pull/20760
(cherry picked from commit 1748ce8295377fe121b5ea9d307bd757c307b475)
Link: https://github.com/openwrt/openwrt/pull/20775
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 913e26b20fb532b47f6da5a16278cfd20deb2f41)
Replace hardcoded numbers with the dt-bindings drive strength macros
defined in "dt-bindings/pinctrl/mt65xx.h".
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20894
(cherry picked from commit 2c667f2df4dac12386c7081f68cf02d7f95a9faa)
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20773
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 9f8c60c2c8589dd6b7ec51c9b1931e69da0ed8bb)
Specification
-------------
- SoC : MediaTek MT7986AV quad-core ARM Cortex-A53 2GHz
- RAM : DDR4 512Mbytes, Nanya Technology NT5AD256M16E4
- Flash : 128Mbytes NAND Flash, ESMT F50L1G41LB
- WLAN : MediaTek MT7976DAN, MediaTek MT7916AN, MediaTek MT7976AN
- 2.4GHz : b/g/n/ax, Multi User MIMO
- 5GHz : a/n/ac/ax, Multi User MIMO
- 6GHz : ax, Multi User MIMO
- Ethernet : 10/100/1000 Mbps x4, LAN (MediaTek MT7531AE)
10/100/1000/2500 Mbps x1, WAN (MaxLinear GPY211C0VC)
- UART : 1x4 pin header on PCB
- [J1] 3.3V, TX, RX, GND (115200, 8N1)
- Buttons : WPS, Reset
- Switches : Rfkill Slide Switch
- USB : 1x USB 3.0 (MediaTek MT7986AV peripheral)
- FAN : 1x Fan (off - slow - fast)
- LEDs : 1x Power (Blue)
1x CPU (Blue)
1x Wi-Fi 6GHz (Blue)
1x Wi-Fi 5GHz (Blue)
1x Wi-Fi 2.4GHz (Blue)
4x LAN activity (Blue)
1x WAN activity (Blue)
1x USB 3.0 (Blue)
- Power : 12VDC, 3.5A (Center positive polarity)
MAC address
-----------
+-----------+-------------------+------------------------+
| Interface | MAC | Algorithm |
+-----------+-------------------+------------------------+
| WLAN 2.4G | 58:86:94:xx:xx:xx | label1 |
| WLAN 5G | 5A:86:94:xx:xx:xx | label2 with LA Bit set |
| WLAN 6G | 5A:86:94:xx:xx:xx | label1 with LA Bit set |
| WAN | 58:86:94:xx:xx:xx | label1 + 1 |
| LAN | 58:86:94:xx:xx:xx | label1 + 3 |
+-----------+-------------------+------------------------+
The WLAN 2.4G MAC address (label1) was found in 'Factory' partition, 0xA0004
The WLAN 5G MAC address (label2) was found in 'Factory' partition, 0x4
Installation
------------
1. Download the OEM recovery software (ipTIME Firmware Wizard (11ac))
from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router (keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router (LAN port) to the PC
6. Run the OEM recovery software and follow the instructions
7. Select the *squashfs-factory.bin file during the router recovery process
8. Wait for the router to boot from *squashfs-factory.bin
Note: The router will automatically reboot if no file is uploaded within
55 seconds.
Fan Control
------------
The fan speed is controlled by writing a value from 0 to 2 to the
`fan1_target` file.
```
cd /sys/devices/platform/gpio-fan/hwmon/hwmon2
echo '0' > fan1_target // off
echo '1' > fan1_target // slow
echo '2' > fan1_target // fast
```
Limitation: Enabling Wi-Fi 6E
----------
Wi-Fi 6E (6GHz) does not work out of the box on LuCI.
After installation, you need to configure a few settings in the `radio1`
and `default_radio1` sections of the `/etc/config/wireless`.
Once you have made these changes, you can enable and use Wi-Fi 6E.
In the `radio1` section, you need to add three common options:
- band: must be set to `6g`
- country: a valid country code for the 6GHz band
- channel: a preferrend scanning channel (PSC) for 6GHz
In the `default_radio1` section, you need to add the SSID and key:
- ssid: The public name of your Wi-Fi network
- key: The Wi-Fi password
- encryption: must be set to either `sae` for WPA3 or `owe` for OWE
(open network)
Example:
```
config wifi-device 'radio1'
...
option band '6g'
option country 'KR'
option channel '37'
...
config wifi-iface 'default_radio1'
...
option ssid 'my_wifi_6e_name'
option key 'my_strong_password1234'
option encryption 'sae'
...
```
Note: A list of all the 6GHz PSC channels:
```
5, 21, 37, 53, 69, 85, 101, 117, 133, 149, 165, 181, 197, 213, and 229
```
Limitation: Maximum Transmit Power (Wi-Fi 6E)
----------
The maximum transmit power is currently broken. In the drop-down menu,
you can only choose between "driver default" and "255 dBm (2147493647
mW)". There is currently no workaround for the issue. Please leave the
maximum transmit power set to "driver default".
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19763
(cherry picked from commit 2503e5bc3798556c10e7027b0013fdeda07ced1f)
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20773
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit ea96f50747de0a788822e1b8ad8621975cf17dbc)
Hardware
--------
MediaTek MT7981 WiSoC
512MB DDR4 RAM
128MB SPI-NAND
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
4 LAN MediaTek MT7531 PHY
1 WAN RTL8221B-VB-CG 2.5Gbps PHY
UART: 115200 8N1 3.3V
USB2 Port
PoE on WAN Port
MAC:
LAN MAC: label mac
WAN MAC: label mac + 1
2.4G MAC: label mac
5G MAC: label mac + 1 with LA bit set
Gotchas:
WAN LED does not light up (might require further DTS tweaks)
PoE on WAN port was not tested
This commit is heavily based on WR3000H one, I've just ported DTS differences
from the official image to get USB support and proper LED mapping.
Installation
------------
[Untested as I've received and used a transitional image from Cudy]
1. Connect to the serial port as described in the "Hardware" section.
2. Power on the device + press reset pin. Keep pressing reset pin to enter the U-Boot shell.
3. Download the OpenWrt initramfs image. Place it on an TFTP server
connected to the Cudy LAN ports. Make sure the server is reachable at
192.168.1.88. Rename the image to "cudy3000p.bin"
4. Download and boot the OpenWrt initramfs image.
$ tftpboot 0x46000000 cudy3000s.bin; bootm 0x46000000
5. Transfer the OpenWrt sysupgrade image to the device using scp.
Install with sysupgrade.
Signed-off-by: Michal Halva <hedik01@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19636
(cherry picked from commit 04e9d154f209c0390d962c10e75ed3c49bd5a9e9)
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Link: https://github.com/openwrt/openwrt/pull/20830
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 51108508f10eb25f99395ec9334f996813bc5a22)
Backport upstream patch to add support for the ESMT F50L1G41LC flash
chip. It is used in multiple Cudy products manufactured starting
November 2025.
(cherry picked from commit 9424b2b78626702012dc73616bfd21029712b5f7)
Link: https://github.com/openwrt/openwrt/pull/20963
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 6ff763e78ceff83ffef7db08f7cc364bbc05ca50)
This board is also as known as E-Life ETR631-T/ETR635-U.
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB DDR3
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain telnet access:
1. Login into web interface, and download the configuration.
2. Uncompress the configuration:
* Enter fakeroot if you are not login as root.
tar -zxf <filename>.tar.gz
3. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
4. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; telnetd; ) &
5. Repack the configuration:
tar -zcf backup.tar.gz etc/
6. Upload new configuration via web interface, now you can connect to
KOMI A31 via telnet.
Flash instructions:
1. Connect to KOMI A31, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-konka_komi-a31-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-konka_komi-a31-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20357
(cherry picked from commit 8a7de107d89fe33c811603ce997a09ea7394a478)
[rebase uboot patches upon 24.10 branch]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20595
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit a167e68c76444c8510e10aeaafa21f986098164e)
Additional work building upon f6e0f57be0af
Add more explict guards around the unsupported generation of the initramfs
images and suppress requirement for certain others.
Fixes: https://github.com/openwrt/openwrt/issues/20151
Fixes: https://github.com/openwrt/asu/issues/1499
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20460
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit f5fd7ef8886faadc654b627e5e4b4484c6ca31d7)
(cherry picked from commit 4ead11296a30276d5aafb0a326bad18a61fd74b5)
The imagebuilder is not intended to build initramfs images. Some
profiles attempt to do this and succeed, due to buildroot leaking
the initramfs-kernel into staging_dir; others attempt it, but fail
due to not having initramfs binaries present in the imagebuilder.
Fix this by adding an explict guard around the unsupported generation
of the initramfs images. This saves space and time during imagebuilder
runs, fixes those that are currently broken and protects against future
breakage for profiles that inadvertently work now.
Fixes: https://github.com/openwrt/openwrt/issues/20151
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20347
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit f6e0f57be0afd1baae8376c8c58535f9a9fe6e4d)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 29397011ccef8cca2b26ebf8e2189224a88228bd)
This adds the required image receipt to generate a vendor ui compatible
initramfs-factory image, that can be used to flash the final sysupgrade
image.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20409
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 4e81893953c8721aefc45e7053b85f20b621eaa8)
GL.iNet shipped a hardware change of the WAN PHY going from the MaxLinear
GPY211C to the Airoha EN8811H.
Signed-off-by: Matthew Bilker <me@mbilker.us>
Link: https://github.com/openwrt/openwrt/pull/18799
(cherry picked from commit 8d30e07180367cdeb4affd79adead6e1025355c9)
Link: https://github.com/openwrt/openwrt/pull/20307
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 10363b5e264d60461b10e9858714609ec5ef35cb)
The devices are basically identical. The RAX3000Me can be with
ddr3 RAM.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19760
(cherry picked from commit 23f016cf1e76aaeb41da70c520dc65d34b5be741)
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19991
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 08478c517ea32e5155346db4ce7d62d4fd2761d2)
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3GHz
- RAM : DDR3 256Mbytes, ESMT M15T2G16128A
- Flash : 128Mbytes NAND Flash, ESMT F50L1G41LB
- WLAN : MediaTek MT7976CN dual-band Wi-Fi 6
- 2.4GHz : b/g/n/ax, MU-MIMO
- 5GHz : a/n/ac/ax, MU-MIMO
- Ethernet : MediaTek MT7531AE
- LAN : 10/100/1000 Mbps x4
- WAN : 10/100/1000 Mbps x1
- UART : 1x4 pin header on PCB
- [J6] TX, RX, GND, 3.3V (115200, 8N1)
- Buttons : WPS, Reset
- LEDs : 1x CPU (Amber)
1x Wi-Fi 5GHz (Amber)
1x Wi-Fi 2.4GHz (Amber)
1x WAN activity (Amber)
4x LAN activity (Amber)
- Power : 12VDC, 1A (Center positive polarity)
MAC address
-----------
+-----------+-------------------+-----------------------+
| Interface | MAC | Algorithm |
+-----------+-------------------+-----------------------+
| WLAN 2.4G | B0:38:6C:48:xx:xx | label |
| WLAN 5G | B2:38:6C:48:xx:xx | label with LA Bit Set |
| WAN | B0:38:6C:48:xx:xx | label + 1 |
| LAN | B0:38:6C:48:xx:xx | label + 3 |
+-----------+-------------------+-----------------------+
The WLAN 2.4G MAC was found in 'Factory' partition, 0x4
Installation
------------
1. Download the OEM recovery software from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router(keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router(LAN port) to the PC
6. Replace a file in the OEM recovery software with the file from step 2
7. Run the OEM recovery software and follow the instructions
8. Wait for the router to boot from *squashfs-factory.bin
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19368
(cherry picked from commit aea6d1bf5eb579614dcc12c3b2c7215b7cd985ac)
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19939
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit cd0b1a209fb243736d28e554f26ff446cb67c60a)
Adds the capability to flash the factory image using the OEM recovery
software, ipTIME Firmware Wizard(11ac).
Installation
------------
1. Download the OEM recovery software from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router(keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router(LAN port) to the PC
6. Run the OEM recovery software and follow the instructions
7. Select the *squashfs-factory.bin file during the router recovery process
8. Wait for the router to boot from *squashfs-factory.bin
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19497
(cherry picked from commit 0e4a69e340083f78ef1e6ec148042d8cde415b78)
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19928
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit faf4f1e49ef296c4efd0fa4da57d1f2cbc5b90f9)
This file should be generated automatically at runtime by the kernel
build system.
Link: https://github.com/openwrt/openwrt/pull/19473
(cherry picked from commit e53c53b7d59d444a7964fbeaa66609f13c1133f9)
Link: https://github.com/openwrt/openwrt/pull/19839
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f894fa971b6135f14700cb8850856dec548d23b8)
PR of openwrt:main: https://github.com/openwrt/openwrt/pull/19512
OpenFi 6C is a portable Wi-Fi 6 travel router based on MediaTek MT7981B+MT7976CN.
Two slightly different versions have been sold. The V1 board has a green color and lacks the modem LED. The V2 board is black and has a LED for the modem.
Specifications:
- SoC: MediaTek MT7981B (Filogic 820) 1.3GHz dual-core ARM Cortex-A53
- RAM: 1GB DDR4
- Flash: 256MB SPI NAND
- Wireless: 2.4GHz/5GHz 802.11ax
- Ethernet: 1x 10/100/1000M LAN
- USB: 1x USB 3.0 Type-A port
- Expansion: M.2 slot for 5G modem
- Cooling: PWM-controlled fan
- Buttons: Reset, Mode switch
- LEDs: System, Ethernet, 5G WiFi, Modem status
**Installation via U-Boot web page**
1. Set static IP 192.168.21.2/255.255.255.0 on your computer.
2. Connect to the Ethernet port and hold the reset button while booting the device. Wait for 6-8 seconds, and release the reset button.
3. Open U-boot web page on your browser at http://192.168.21.1
4. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
5. Wait for automatic reboot.
**Installation via sysupgrade**
Flash the sysupgrade file via LuCI upgrade page without saving the settings.
Signed-off-by: Jiasheng Zhu <newbanyaya@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19512
(cherry picked from commit 536a25ebf849b2de22792786b4c6f0c15471ee93)
Link: https://github.com/openwrt/openwrt/pull/19536
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 191d73846909142c694c6c24e4b8334f9f3d4df1)
Currently, if OEM recovery flashes OpenWrt to second ubi1,
OpenWrt cannot boot. With this commit, recovery image is built
with initramfs kernel, so that it can boot from either ubi or ubi1.
This adds an extra step to OpenWrt installation from OEM:
user needs to sysupgrade from initramfs to full system.
Signed-off-by: Mateusz Krzak <kszaquitto+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18878
(cherry picked from commit 6615c8cfc85f1373cf93a9fc08cb1cb3bbefc964)
Signed-off-by: Mateusz Krzak <kszaquitto+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19595
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 124f61eddbdc668ef5fc709b90510278f041bb64)
**Huasifei WH3000 Pro**
Portable Wi-Fi 6 travel router based on MediaTek MT7981A SoC. MT7981B+MT7976CN+RTL8221B Dual Core 1.3GHZ with 5G modems module and PWM Fan.
**Specifications**
SoC: Filogic 820 MT7981A (1.3GHz)
RAM: DDR4 1GB
Flash: eMMC 8GB
WiFi: 2.4GHz and 5GHz with 3 antennas
Ethernet:
1x WAN (10/100/1000M)
1x LAN (10/100/1000/2500M)
USB: 1x USB 3.0 port
Two buttons: power/reset and mode (BTN_0)
LEDS: blue, red, blue+red=pink
UART: 3.3V, TX, RX, GND / 115200 8N1
**Installation via U-Boot rescue**
1. Set static IP 192.168.1.2 on your computer and default route as 192.168.1.1
2. Connect to the WAN port and hold the reset button while booting the device.
3. Wait for the LED to blink 5 times, and release the reset button.
4. Open U-boot web page on your browser at http://192.168.1.1
5. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
6. Wait for the router to flash the new firmware.
7. Wait for the router to reboot itself.
**Installation via sysupgrade**
Just flash sysupgrade file via [LuCI upgrade page](http://192.168.1.1/cgi-bin/luci/admin/system/flash) without saving the settings.
**Installation via SSH**
Upload the file to the router `/tmp` directory, `ssh root@192.168.1.1` and issue a command:
```
sysupgrade -n /tmp/openwrt-mediatek-filogic-huasifei_wh3000-pro-squashfs-sysupgrade.bin
```
**Factory MAC**
You can find your Factory MAC which is mentioned on the box at `/dev/mmcblck0p2` partition `factory` starting from `0x4`
```
dd if=/dev/mmcblk0p2 bs=1 skip=4 count=6 | hexdump -C
```
Cherry-picked from 949d0bd77a
Fixed `green` to `blue` LED in dts, added `SUPPORTED_DEVICES += huasifei,fudy-pro` - to make sysupgrade compatible with factory QWRT/Lede fork firmware.
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19315
(cherry picked from commit db1de8d21fd7f115cc1a6274f031119c9f36eefd)
Link: https://github.com/openwrt/openwrt/pull/19391
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
