cudy ap3000-v1 did not work correctly in failsafe mode
because the address 192.168.1.1 was missing on the eth0 inteface.
it was reachable via it's IPv6 link-local address however.
this commit fixes the issue.
Fixes: https://github.com/openwrt/openwrt/issues/20750
Signed-off-by: Martin Nadvornik <martin.nadvornik@gmx.at>
Link: https://github.com/openwrt/openwrt/pull/21172
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit e5cd6461c905184db8f49692f931b20fec4b819e)
The ports are physically labelled in reverse order on the device.
This patch aligns logical names with physical ones.
LED order on front of device is correct after this patch.
Fixes: 9d66b8b312
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Link: https://github.com/openwrt/openwrt/pull/20528
(cherry picked from commit 887cab883b)
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Link: https://github.com/openwrt/openwrt/pull/21173
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix Totolink X6000R image failing to upgrade via sysupgrade due to an
incorrect upgrade case. The fallback upgrade path used the NAND upgrade
routine, which caused the "layout volume not found" error on NOR flash
devices. By adding a specific case for this board, sysupgrade now uses
`default_do_upgrade`, which is compatible with the NOR flash layout.
Fixes: 7cd10ad
Signed-off-by: Ayra Hikari <ayrahikari@linuxmail.org>
(cherry picked from commit 7cd10add2d)
Link: https://github.com/openwrt/openwrt/pull/20674
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification :
- SOC : Mediatek MT7981B (1.3GHz)
- RAM : 256MB
- Flash : 16MB SPI NOR
- Ports : 4 LAN (1G) & 1 WAN (1G)
- WIFI : MediaTek dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MIMO 2x2
- 5 GHz : a/n/ac/ax, MIMO 2x2
- Buttons : Reset & WPS/Mesh
- LEDS : WAN (Green), Status (Red & Blue)
- Power : 12V1A
Install via OEM web ui:
Upload the sysupgrade image to firmware upgrade page on OEM web ui
Install via recovery / revert to stock firmware:
1. Unplug from power
2. Download the Sysupgrade (for openwrt installation) or OEM Factory image (for revert to stock firmware)
3. Set your computer ethernet IP to 192.168.1.X, subnet 255.255.255.0 (X=your chosen ip number ranging from 2-254)
4. Press and hold reset button while turn on / plug power adapter to the router. Wait untill ALL LAN green LED turn on, then release the reset button.
5. Plug the LAN cable from your computer into LAN 1 port then open web browser, and type in the address column : 192.168.1.1
6. Upload the sysupgrade / oem factory image
7. Wait until the router finished flashing (the router will reboot)
8. Set ethernet ip to dhcp
9. Open 192.168.1.1 (for openwrt install) / 192.168.0.1 (for OEM firmware)
Signed-off-by: Ari Kurniawan <noobhek@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20035
(cherry picked from commit 7cd10add2d)
Signed-off-by: Ari Kurniawan <noobhek@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20674
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since kernel 6.1, the Watchguard Firebox T10 can't boot anymore due to
increased kernel size.
This commit introduces the zImage loader from 7d768a9 to boot the kernel.
This is required, since the U-Boot version used in this device appears
to have a hard limit of 16MB for the kernel size it can handle. The
current kernel size is around 17MB, though, due to kernel page alignment
required for memory protection.
(cherry-picked from commit be7aa5bda40ee05b1dd0b4f4a1bf88e653ef875a)
Signed-off-by: Shine <4c.fce2@proton.me>
Link: https://github.com/openwrt/openwrt/pull/21130
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This PR fixes support for Cudy r700.
Original PR: https://github.com/openwrt/openwrt/pull/18532
Fixed:
- WAN port functionality;
- RESET button;
- Status LED;
- LAN port names consistent with the chassis;
- Merged partitions "debug", "backup" & "firmware" to one partition "firmware" ("debug" & "backup" contained unimportant data);
- Removed redundant DTS elements.
Installation:
To install OpenWRT, you need the intermediate firmware from Cudy. (U-boot is locked). After installing the intermediate firmware, you can install OpenWRT via sysupgrade.
Recovery:
TFTP available.
1. Place the recovery.bin in the serving directory of your TFTP server.
2. Set your IP to 192.168.1.88/24.
3. Press the “Reset” button of Cudy router and hold it. Before the Cudy router is powered on and before TFTP start to download the firmware, don't release the “Reset” button.
4. Power on the Cudy router.
5. You can release the reset button only when TFTP starts downloading firmware.
6. When the SYSTEM LED turns solid green, the upgrade is complete.
Fixes: 75403dd1d0 ("ramips: add support for Cudy R700")
Link: https://github.com/openwrt/openwrt/pull/20756
(cherry picked from commit 35a86267e9)
Signed-off-by: Marcin Leksmark <lexmark3200@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/21068
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is the same hardware as the Cudy WR2100 that's
had support for some time now, just without the WLAN
hardware.
This PR is mostly copied from the commit that added
support for the WR2100, here: 3501db9
Specifications:
SoC: MT7621
CPU: 880 MHz
Flash: 16 MiB
RAM: 128 MiB
Ethernet: 5x Gbit ports
Installation:
There are two known options:
The Luci-based UI.
Press and hold the reset button during power up.
The router will request 'recovery.bin' from a TFTP server at
192.168.1.88.
Both options require a signed firmware binary.
A signed firmware can be found in GitHub PR #18532.
R4 & R5 need to be shorted (0-100Ω) for the UART to work.
Link: https://github.com/openwrt/openwrt/pull/18532
Signed-off-by: David DeGraw <degraw@fastmail.com>
(cherry picked from commit 75403dd1d0)
Link: https://github.com/openwrt/openwrt/pull/21068
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch adds support for Cudy C200P.
Because v24.10 stable has no regulator definition, so we cannot make simple cherry-pick. We need another DTS file.
Specifications:
SoC: MediaTek MT7621AT
RAM: 256 MB (DDR3)
Flash: 16 MB (NOR)
POE Chip: IP804AR
Interfaces:
Switch: 1 WAN, 4 LAN (Gigabit)
Gigabit RJ45 PoE Ports on 2~5
Max Power on a Single PoE Ports 30W
PoE Ports : The PoE ports comply with IEEE 802.3at/af standards.
Ports: 1 USB-A 3.0 Ports
LED:
System
PoE Max Status
Link/ACT/PoE Status of Each PoE Port
Physical Buttons:
Reset Button
Power Input:
DC Jack
Power Methods:
DC: 54V 1.11A
802.3at/af PoE
Passive PoE: 24/48V
Max Power Consumption (W):
Total: 60W
PoE: 55W
PoE (when USB Device is plugged in): 50W
No PoE: 5W
Installation:
To install OpenWRT, you need the intermediate firmware from Cudy. (U-boot is locked). After installing the intermediate firmware, you can install OpenWRT via sysupgrade.
Recovery:
TFTP available.
1. Place the recovery.bin in the serving directory of your TFTP server.
2. Set your IP to 192.168.1.88/24.
3. Press the “Reset” button of Cudy router and hold it. Before the Cudy router is powered on and before TFTP start to download the firmware, don't release the “Reset” button.
4. Power on the Cudy router.
5. You can release the reset button only when TFTP starts downloading firmware.
6. When the SYSTEM LED turns solid green, the upgrade is complete.
Serial:
1. Serial connection parameters: 115200 / 8N1
2. Serial connection voltage: 3.3V
PoE is not supported at the time of PR. The IP804R chip is not yet supported by OpenWRT.
Signed-off-by: Marcin Leksmark <lexmark3200@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/21064
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is an industrial 4G router equipped with OpenWrt SNAPSHOT OEM
customized version
WARNING: The original firmware device tree is modified from evb
boards, and the device tree name is evb board. This submitted device
tree is a modified version, which deletes the non-this-device parts
and adds GPIO watchdog.
Specification:
- SoC: MediaTek MT7628DAN
- Flash: 16 MB
- RAM: 64 MB
- Power: DC 5V-36V 1.5A
- Ethernet: 1x WAN/LAN, 3x LAN (10/100 Mbps)
- Wireless radio: 802.11n 2.4g-only
- LED:
System/Power (PWR): Always Off
Modem (NET): GPIO/3 active-low
LAN: Always On
RF (Modem Signal): GPIO/2 active-low
WIFI: GPIO/44 active-low
- Button:
WPS / RESET: GPIO/11 active-low
- UART: 1x UART on PCB - 115200 8N1
- GPIO Watchdog: GPIO/0 mode=toggle timeout=1s
- Modem: 1x Built-in modem on board (Power: GPIO/4 active-high)
- SIM Slots: 1x SIM Slots
Issue:
- Factory partition not store mac address on original firmware
Flash instruction:
Using TTL:
1. Connect the board to the computer via TTL.
2. Enter original firmware failsafe mode.
3. Use wget download firmware to board /tmp
4. Use command "mtd -r write openwrt-ramips-mt76x8-hongdian_h8850-v20-squashfs-sysupgrade.bin firmware"
to flash
Original Firmware Dump / More details:
https://blog.gov.cooking/archives/research-hongdian-h8850-v20-and-flash.html
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Tested-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20259
(cherry picked from commit 23a070dfb1)
Link: https://github.com/openwrt/openwrt/pull/21007
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
GL-MV1000 external SD controller was broken by a recent kernel update
between OpenWRT releases 24.10.2 and 24.10.3 due to a mistake in Device
Tree: "regulator-gpio" was defined without required "gpios" property.
Since "no-1-8-v" property is also defined for this controller
a switchable vqmmc-supply regulator performs no function - a fixed 3.3V
IO voltage will always be used.
This regulator definition was probably added by mistake from a Device
Tree from another device.
Remove incomplete vcc_sd_reg1 regulator definition to fix this issue.
Issue discussion for reference: openwrt/openwrt#20309
Upstream commit: 6f2325b23d
Signed-off-by: Mikhail Zadorozhnyi <zador.blood.stained+git@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/20378
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ASUS TUF-AX4200Q(TUF 小旋风Pro WiFi6 AX4200) is a home router that adds an additional 2.5G Ethernet port to ASUS TUF-AX4200.
Hardware
- - - - - - - -
- SOC : MediaTek MT7986
- RAM : 512MB DDR3
- FLASH : 256MB SPI-NAND (Winbond W25N02KV)
- WIFI : Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
- ETH : MediaTek MT7531 Switch
MaxLinear GPY211C 2.5 N-Base-T PHY (WAN)
MaxLinear GPY211C 2.5 N-Base-T PHY (LAN)
- UART : 3V3 115200 8N1 (Pinout silkscreened / Do not ocnnect VCC)
Installation
- - - - - - - -
Vendor-UI Method:
1. Download or make the OpenWrt initramfs.trx image
2. Connect the PC via LAN to one of the yellow router ports and wait until your PC to get a DHCP lease.
3. Browse to http://192.168.50.1/
4. If your router is brand new, finish the setup process and log into the Web-UI.
5. Navigate to Administration -> Firmware Upgrade and upload the downloaded OpenWrt image.
6. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using SCP and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
TFTP Method:
1. Download the OpenWrt initramfs image.
Copy the image to a TFTP server reachable at 192.168.1.70/24.
Rename the image to tufax4200q.bin.
2. Connect the PC with TFTP server to the TUF-AX4200Q.
Set a static ip on the ethernet interface of your PC.
(IP address: 192.168.1.70, subnet mask: 255.255.255.0)
Connect to the serial console,
interrupt the autoboot process by pressing '4' when prompted.
3. Download & Boot the OpenWrt initramfs image.
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 tufax4200q.bin
$ bootm 0x46000000
4. Wait for OpenWrt to boot.
Transfer the sysupgrade image to the device using SCP and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
(based on support for ASUS RT-AX52 by achterin and trx image generation by remittor)
Link: https://github.com/openwrt/openwrt/pull/20900
(cherry picked from commit e7086d7a2f)
Signed-off-by: Brian Lee <larte332@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21036
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch adds support for D-Link DIR-2660 A2.
Based on the commit: https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=b5dd746cbb1aaf91f4b68e9f3eda97413550d904,
Both devices look identical, except for the A1/A2 designation.
You can safely install the A1 firmware for the A2 – I've been testing it for several months as a DUMB AP – without any problems.
Specifications:
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
WiFi 5G (white), USB 3.0 (white), USB 2.0 (white)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
Signed-off-by: Marcin Leksmark <lexmark3200@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20020
(cherry picked from commit 485f9b0d31)
Link: https://github.com/openwrt/openwrt/pull/21113
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
According to the factory uboot and firmware[1], the ubi size is set
to 512 MiB (0x20000000) and it exceeds the size of the flash, after
that the uboot and kernel resizes it to 114.5 MiB (0x7280000) instead
of 114.125 MiB (0x7220000). The mismatch of the ubi size causes
kernel fails to read ubi volumes and throws panic.
Trim whitespaces while at it.
1. https://github.com/immortalwrt/immortalwrt/issues/2123#issuecomment-3523744128
Fixes: c908fc7d95 ("mediatek: add support for Zbtlink ZBT-Z8102AX v2")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20769
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d2fa070f70)
[rebased upon 24.10 branch]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/21085
Signed-off-by: Robert Marko <robimarko@gmail.com>
This partially reverts 78d259e7d2.
That commit broke mounting the root fs on Sophos RED 15w due to
partition size mismatch, and changed the partition sequence, causing
the OpenWrt partition numbers to change from mtd3:kernel/mtd4:ubi to
mtd4:kernel/mtd5:ubi.
Fixes: 78d259e7d2 ("mpc85xx: fix some dtc warnings")
(cherry-picked from commit 09e7b24ceb)
Signed-off-by: Shine <4c.fce2@proton.me>
Link: https://github.com/openwrt/openwrt/pull/21062
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
