Backport fixes for Airoha pinctrl driver for PHY LED and MDIO bus. This
fix a copy-paste error for PHY LED and a misconfiguration for MT7530
embedded Switch MDIO bus GPIO pin to permit usage of external PHYs.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 35ff70e8073635d60b36875e62c9ba62b4af9182)
(cherry picked from commit dc11868486deb6688a1bb2fa4b04e84ce347eae8)
Add the NPU and reserved memory node for AN7581 dtsi since it's not
supported.
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 3dca527e6d1e19aa97ece32c27af5a59ecbe646d)
(cherry picked from commit 6a7b16e61692fdab94094a5f1577311cbc611870)
Major backport of upstream patch for support of multiple feature of the
Airoha Ethernet driver.
Feature backported are TSO, Jumbo packet, Offload and initial Wlan
Offload support.
Link: https://github.com/openwrt/openwrt/pull/19816
(cherry picked from commit 9d3009f426d5b5ca4eb120989d7d5776175a97d3)
[ add missing kconfig flag ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 671f4d53acf183af80641362f5b6af0295083277)
Backport trivial fixes from upstream related to pinctrl and ethernet
driver.
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 354d7472d5c6b06e0c11606e1b9104a5f7d24374)
(cherry picked from commit bac7ee02f93bec5886e2eb73e383442509c6a828)
Backport patch adding support for AN7581 Ethernet PHY based on the same
Mediatek embedded Switch PHY.
Link: https://github.com/openwrt/openwrt/pull/19816
(cherry picked from commit 0adaeff5eea122891d255e9ed743c617e91d716e)
[ rework backported patch ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 3b1fc6661a995fd02f1fc05bc83e6c1aeea1cf00)
Replace thermal patch with upstream version. The thermal maintainer
reported that the sysfs entry are considered deprecated and that slope
and offset should be handled internally to the driver.
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit a713260966003f2941e1327a7158d542689967dc)
(cherry picked from commit a6e8cbdf533d049d0d769784f2d8f07f78707323)
This board is also as known as E-Life ETR631-T/ETR635-U.
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB DDR3
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain telnet access:
1. Login into web interface, and download the configuration.
2. Uncompress the configuration:
* Enter fakeroot if you are not login as root.
tar -zxf <filename>.tar.gz
3. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
4. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; telnetd; ) &
5. Repack the configuration:
tar -zcf backup.tar.gz etc/
6. Upload new configuration via web interface, now you can connect to
KOMI A31 via telnet.
Flash instructions:
1. Connect to KOMI A31, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-konka_komi-a31-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-konka_komi-a31-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20357
(cherry picked from commit 8a7de107d89fe33c811603ce997a09ea7394a478)
[rebase uboot patches upon 24.10 branch]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20595
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit a167e68c76444c8510e10aeaafa21f986098164e)
Hardware
--------
RockChip RK3568 ARM64 (4 cores)
1/2GB LPDDR4 RAM
2x 2500 Base-T (PCIe, r8125b)
1 LED (Power)
1 Button (Reset)
Micro-SD Slot
2x USB 3.0 Port
12V DC Jack
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card using
dd.
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/19990
(cherry picked from commit d76a77427017ee6356d3d0f9be61927c03748a09)
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20618
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit c3b4e8e531b5ae1dbacc5aa74fca520abf33c3e4)
Add support for the Lunzn FastRhino R66S board.
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/19990
(cherry picked from commit 678536740ed58495e654f638f77decb8af18d768)
[rebase patches upon 24.10 branch]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20618
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 32a2193a4877fffeb255c90b1f3c38667ed8bf53)
The High-Speed SD mode stability issue should have been fixed.
Increase the MMC max-frequency to improve the IO speed. We can
still use the sysfs to limit the clock frequency, e.g.
root@OpenWrt:~# echo 25000000 > /sys/kernel/debug/mmc0/clock
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18896
(cherry picked from commit 143cfd6113231c61f38d1b9f5a0ea9ce3cc986c5)
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20258
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit a902c0d02037ada89e39df1483fe4e4bd8bb7296)
This new feature has some improvements for random RW performance.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18896
(cherry picked from commit db76fe6a02ed5bf3b545a8a09d6112ed4039edaf)
[removed kernel 6.12 patches]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20258
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 0be05cdf72cc19d8b1121817b23d1b96d040e610)
The MT7628 programing guide shows that the correct DTOC unit is
1048576 clocks instead of 65536 clocks. This value is also used
by linux upstream mtk-sd driver. Correct the DTOC register and
also round up its value.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18896
(cherry picked from commit e69c867cdf62623613c9026b577b290edae780a1)
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20258
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 0ed371472cc3b6ab38cec88c073ca84c15938c4a)
- Fix MMC bus IO voltage. The GPIO voltage of mt762x series SoCs
is fixed 3.3V. There are no visible registers that can control
the voltage level. Also add "no-1-8-v" property to indicate that
MMC controller doesn't support 1.8V IO.
- Drop useless property "enable-active-high". These dummy fixed
voltage regulators are not controlled by the GPIO. We don't need
to set the GPIO polarity.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18886
(cherry picked from commit afdf88b9a165710e6132fab6ec245a61f4394d6e)
[rebased upon 24.10 branch]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20258
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 550fa37533ad7b089bdeac40da2ea9abefa53383)
gpio-leds were not working on F@ST3864OP before https://github.com/openwrt/openwrt/pull/17527 was merged.
This pull request adds definitions for all LEDs, including the previously
non-working WAN LEDs.
Signed-off-by: Hang Zhou <929513338@qq.com>
Link: https://github.com/openwrt/openwrt/pull/20533
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 6de96914e5cb57687588a77dab08afe3149c21f5)
(cherry picked from commit aa03dfeb96cfe6a7f4d00cfe03529d8a06d4568e)
If the environment variable `CI` is set, ccache will enable the CMake
option CCACHE_DEV_MODE by default. This leads to differing behaviour
between local and CI builds which takes quite some time to debug. 🤯
Achieve consistent behaviour between local builds and CI builds by
setting CCACHE_DEV_MODE. Set it to OFF, because CCACHE_DEV_MODE amongst
other settings like linker choice, enables -Werror, which will lead to
potential compilation failures when the host compiler is updated. Using
-Werror for host utils is not desirable, because the compiler version
used is not controlled by the OpenWrt build system and host utils should
compile successfully on an as wide range of host OSes as possible.
Reported-by: Roman Azarenko <roman.azarenko@iopsys.eu>
Signed-off-by: Andreas Gnau <andreas.gnau@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/20290
(cherry picked from commit 6f32c657db55a2e34f659d81d56aa385aaa7d69d)
Link: https://github.com/openwrt/openwrt/pull/20334
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit a38b0c94dd02a03ab14f55bc98b2aa24561aed5a)
Mold does not really work on MacOS, when attempting to use it for example
for ubus:
mold: get_self_path is not supportedcollect2: error: ld returned 1 exit status
Which was introduced by [1] so it seems that MacOS is not supported, so
lets make it non selectable when MacOS is the host.
[1] f9a37e9dd4
Link: https://github.com/openwrt/openwrt/pull/18575
(cherry picked from commit 3c65dc367827bc06bd45f7eb375c59192deb0a75)
Link: https://github.com/openwrt/openwrt/pull/20621
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 99e62c21c6eaf1bc68e56d279d3aad005f52e113)
Now that we have a board file, add calibration variant for TP-Link
Archer C60 v2 and add ipq-wifi package for it.
Tested-by: Semih Baskan <strstgs@gmail.com>
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20496
Link: https://github.com/openwrt/openwrt/pull/20497
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 2d758300e38b3c214a5c63bcfab163b4b1ebd019)
With further investigation it was found a race in generating .itb images
that include a RootFS caused by the mkits.sh and the mkimage.
Due to the fact that mkits.sh generates a .pagesync image of the passed
rootfs, it can happen that, concurrently, mkimage can be called at the
same time mkits.sh is creating another .pagesync for the same rootfs.
This cause mkimage to use an half made rootfs.pagesync creating a
corrupted image.
To address this, also protect the mkimage with the same lock used for
mkits.sh preventing any kind of concurrent usage/generation of the
rootfs.pagesync blob
Fixes: 52cc9d82f1 ("kernel: rework Initramfs locking logic")
Link: https://github.com/openwrt/openwrt/pull/20492
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 3de1bbd5aeb542de9a4b20eff0f6bbf1767fd6b9)
(cherry picked from commit bdb89ee6dff4742f2d7bcf101077ee6f9f8031f7)
Currently, building at91 subtargets via image builder will fail as the
required built at91bootstrap is not present in the image builder at all
since its presumed to be in the binary directory which obviously does not
exist yet.
So, lets install the at91bootstrap binary into image staging directory and
use that instead
Link: https://github.com/openwrt/openwrt/pull/18414
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit a947be41b721a7c521d23981adaf06ebd1ef5dfe)
(cherry picked from commit debc420622f9ed56fd2f23d455f831a22cf5a256)
Currently, building at91 subtargets via image builder will fail as the
required built u-boot is not present in the image builder at all since its
presumed to be in the binary directory which obviously does not exist yet.
So, lets install the u-boot binary into image staging directory and use
that instead.
Link: https://github.com/openwrt/openwrt/pull/18414
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 4724331d7037e61527e7da7253cdaa4a90b1d302)
(cherry picked from commit c5d7ef41f87bcf7b0067bdfd81b2f2572bc3c3a9)
Currently, kmod-usb-ohci,kmod-at91-udc and kmod-usb-gadget-eth are included
as the default packages for all at91 subtargets.
However, this is breaking image builder as kmod-at91-udc is not being built
on sama7 since it depends on USB_SUPPORT and sama7 does not have USB support
enabled in the kernel as its not supported upstream so its not even
selectable in the config.
So, move to include these as default packages only for sama5 and sama9x as
both of those have USB support enabled.
Fixes: #18407
Link: https://github.com/openwrt/openwrt/pull/18413
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 02d3aa72bb72af1a9405bc3fef977e48d20157a5)
(cherry picked from commit be73a7f033174eeba36b0a5c950aa0d58fbdee3c)
Now that all packages that relied on the skip mechanism are selected
via BUILD_DEVICES or by defaulting for the subtarget drop them from
individual DEVICE_PACKAGES so that Image Builder works again for armv7.
Fixes: #18411
Link: https://github.com/openwrt/openwrt/pull/18462
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 8cb7919a137b4f2b1a207b43ecbac2af49937f24)
(cherry picked from commit d4eb33990b0064e27b8aa48c27cca82df0fe7450)
Currently, ls-rcw package is being included in the individual
profile DEVICE_PACKAGES but using the feature that allows skipping their
inclusion in the end image package list if prefixed with a tilde(~) which
was added in:
377b66990b ("build: introduce support to declare skip package")
But it not added to Image Builder so currently trying to build layerscape
device images in Image Builder will fail with:
ERROR: '~ls-rcw' is not a valid world dependency, format is name(@tag)([<>~=]version)
So, instead of having to rely on support for skipping package installation
and declaring the ls-rcw package in DEVICE_PACKAGES lets select it when
layerscape/armv7 target is selected.
Fixes: #18411
Link: https://github.com/openwrt/openwrt/pull/18462
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 598a0556b7f953db1d37059bb15759a4d88bbd3f)
(cherry picked from commit fa3632f3324194388f87d021ca58b101988a9f30)
Now that all packages that relied on the skip mechanism are selected
via BUILD_DEVICES or by defaulting for the subtarget drop them from
individual DEVICE_PACKAGES so that Image Builder works again for armv8_64b.
Fixes: #18412
Link: https://github.com/openwrt/openwrt/pull/18462
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit c04eaad12a28e8d1ae9af41ea8193f6dd5c1cab6)
(cherry picked from commit 5c6e95c5b45ffef32660b45719f24d6def693f74)
Currently, ls-ddr-phy package is being included in the individual
profile DEVICE_PACKAGES but using the feature that allows skipping their
inclusion in the end image package list if prefixed with a tilde(~) which
was added in:
377b66990b ("build: introduce support to declare skip package")
But it not added to Image Builder so currently trying to build layerscape
device images in Image Builder will fail with:
ERROR: '~ls-ddr-phy' is not a valid world dependency, format is name(@tag)([<>~=]version)
So, instead of having to rely on support for skipping package installation
and declaring the ls-ddr-phy package in DEVICE_PACKAGES lets select it when
layerscape/armv8_64b target is selected.
Fixes: #18412
Link: https://github.com/openwrt/openwrt/pull/18462
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 8a28ddafe7a728b8294a8c8ca5fc92aef7af15d2)
(cherry picked from commit c39bc0375f34f5c5467c573886f145ed127a9bd1)
Currently, ls-dpl package is being included in the individual
profile DEVICE_PACKAGES but using the feature that allows skipping their
inclusion in the end image package list if prefixed with a tilde(~) which
was added in:
377b66990b ("build: introduce support to declare skip package")
But it not added to Image Builder so currently trying to build layerscape
device images in Image Builder will fail with:
ERROR: '~ls-dpl' is not a valid world dependency, format is name(@tag)([<>~=]version)
So, instead of having to rely on support for skipping package installation
and declaring the ls-dpl package in DEVICE_PACKAGES lets select it when
layerscape/armv8_64b target is selected.
Fixes: #18412
Link: https://github.com/openwrt/openwrt/pull/18462
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 84437eeec07716bf68d3e10ffa7baf8d3570fe1f)
(cherry picked from commit 9f630a4141ca41f9102a486d979fdc18f475ac60)
Currently, ls-mc package is being included in the individual
profile DEVICE_PACKAGES but using the feature that allows skipping their
inclusion in the end image package list if prefixed with a tilde(~) which
was added in:
377b66990b ("build: introduce support to declare skip package")
But it not added to Image Builder so currently trying to build layerscape
device images in Image Builder will fail with:
ERROR: '~ls-mc' is not a valid world dependency, format is name(@tag)([<>~=]version)
So, instead of having to rely on support for skipping package installation
and declaring the ls-mc package in DEVICE_PACKAGES lets select it when
layerscape/armv8_64b target is selected.
Fixes: #18412
Link: https://github.com/openwrt/openwrt/pull/18462
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 2fb3efda0a2fa82f9401a5fdd9a8c03208d560af)
(cherry picked from commit ebcda1d7da1dc4cb470e3de9beace8f63e85ce25)
Currently, fman-ucode package is being included in the individual
profile DEVICE_PACKAGES but using the feature that allows skipping their
inclusion in the end image package list if prefixed with a tilde(~) which
was added in:
377b66990b ("build: introduce support to declare skip package")
But it not added to Image Builder so currently trying to build layerscape
device images in Image Builder will fail with:
ERROR: '~fman-ucode' is not a valid world dependency, format is name(@tag)([<>~=]version)
So, instead of having to rely on support for skipping package installation
and declaring the fman-ucode package in DEVICE_PACKAGES lets select it when
layerscape/armv8_64b target is selected.
Fixes: #18412
Link: https://github.com/openwrt/openwrt/pull/18462
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 22f02beaabf017aa80717f02c37d29a75c552f81)
(cherry picked from commit 975552ea1445cc1d3a25b1ac641ee78d458c7bb9)
Currently, tfa-layerscape packages are being included in the individual
profile DEVICE_PACKAGES but using the feature that allows skipping their
inclusion in the end image package list if prefixed with a tilde(~) which
was added in:
377b66990b ("build: introduce support to declare skip package")
But it not added to Image Builder so currently trying to build layerscape
device images in Image Builder will fail with:
ERROR: '~trusted-firmware-a-ls1012a-frdm' is not a valid world dependency, format is name(@tag)([<>~=]version)
So, instead of having to rely on support for skipping package installation
and declaring the individual TFA packages in DEVICE_PACKAGES we can just
do what other targets do and set BUILD_DEVICES so that TFA packages are
automatically set.
Fixes: #18412
Link: https://github.com/openwrt/openwrt/pull/18462
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 03ab770da5a469e81a659574a66dd2f7275d431e)
(cherry picked from commit 4108db2bd884d247ef7f483856e43541d3279a43)
Currently, bcm63xx-cfe is being installed into kernel build dir, however
that does not work for Image Builder as only certain artifacts from kernel
build dir are included in Image Builder.
So, simply install bcm63xx-cfe into image staging dir so its artifacts can
be used in Image Builder as well.
Fixes: #18408Fixes: #18409
Link: https://github.com/openwrt/openwrt/pull/18463
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 4a7de50769101962fd9ecc15465f6a11f0e81f9f)
(cherry picked from commit 4b7728ba8b1105845eeb76f495142ce6e6a89f75)
Additional work building upon f6e0f57be0af
Add more explict guards around the unsupported generation of the initramfs
images and suppress requirement for certain others.
Fixes: https://github.com/openwrt/openwrt/issues/20151
Fixes: https://github.com/openwrt/asu/issues/1499
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20460
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit f5fd7ef8886faadc654b627e5e4b4484c6ca31d7)
(cherry picked from commit 4ead11296a30276d5aafb0a326bad18a61fd74b5)
The imagebuilder is not intended to build initramfs images. Some
profiles attempt to do this and succeed, due to buildroot leaking
the initramfs-kernel into staging_dir; others attempt it, but fail
due to not having initramfs binaries present in the imagebuilder.
Fix this by adding an explict guard around the unsupported generation
of the initramfs images. This saves space and time during imagebuilder
runs, fixes those that are currently broken and protects against future
breakage for profiles that inadvertently work now.
Fixes: https://github.com/openwrt/openwrt/issues/20151
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20347
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit f6e0f57be0afd1baae8376c8c58535f9a9fe6e4d)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 29397011ccef8cca2b26ebf8e2189224a88228bd)
This adds led aliases for failsafe and upgrade. Before this change the
leds stayed dark in both situations.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20441
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 1afe4ba623936fa42daba5b88d33687ef551ed11)
Link: https://github.com/openwrt/openwrt/pull/20454
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b2119bbaa2fec757801a3b1627a13584c16188c2)
Set the label-mac-device to be able to easily fetch the mac-address of
the device, which is printed on the bottom of the case.
While at it, remove the TODO - the ethernet0 alias is needed to get the
mac from bootloader.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20441
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit deca8fd24bcd039a3784bf83db5541b297def8ff)
Link: https://github.com/openwrt/openwrt/pull/20454
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit c416b8c44cd5fd70d8ae20dd11169c300104ddee)
No 'PKG_CPE_ID' is stored for the kernel package Makefile. This commit
adds this.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
(cherry picked from commit 112f594042581a7b1886452886bb704f7f0e5a69)
(cherry picked from commit 50f98c53353088e4ec6fdad1a966753e95ea499c)
A lot of recent commits in odhcpd main branch are structural/semantic
changes, so instead of adding those changes to 24.10 branch it's better
to focus on the fixes.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 180646ce4b012c721e3cb33f9dca92e5234a739b)
